Skip to main content

Public Initiative Networks (RIP)

By Steve Rogers,
Public Initiative Networks (RIP)
The France THD plan supports the deployment of RIP when private initiative is not sufficient. This deployment of optical fiber represents 43% of the population and is carried out thanks to a mix mixing several technologies (FTTH, wireless technologies, service of increase in speed).

The investment planned for public initiative networks is estimated between 13 and 14 billion euros. This investment is financed half by the operating revenues of the RIPs and the co-financing of private operators.

The rest of the funding comes from the State in two forms:

Fiber optic testing
With an increasingly competitive market, networks must be continuously upgraded and maintained to ensure higher quality and speed of applications and services provided to customers.

The constant evolution of broadband systems imposes on the fiber optic infrastructure to be impeccable to support these applications and services. Fiber optics must be further tested to ensure that the system will achieve the required level of performance. With its most complete range of fiber optic test solutions in the industry, VIAVI Solutions reduces the complexity surrounding these new network architectures and simplifies their testing.
cable technician certification
Today, fiber optic testing is essential for almost all types of networks. Installers, subcontractors, project managers, technicians and engineers working in the field of optical fiber must be competent and capable of understanding, applying, measuring and correctly recording the performance of optical fiber infrastructures.

Comments

Post a Comment

Popular posts from this blog

The most popular method and the method required in TIA-568

By Steve Rogers,
Choice of the reference method Some reference books and manuals show that to establish the reference power for loss, only a reference launch cable, launch and reception cable connected with a coupling adapter or even three reference cables is used.  In fact, industry standards include all three methods to establish a "0dB loss" reference.  The two or three-wire reference methods are acceptable for some tests and are the only way you can test some connectors, but it will reduce the loss you measure in the amount of loss between your reference wires when you set your "  You could start the test with faulty launch wires, which would cause all loss measurements to be incorrect.  This means that the inspection and testing of the reference cables are very important, in order to ensure that they are in good condition.  You could start the test with faulty launch wires, which would cause all loss measurements to be incorrect.  This means that the inspection and...
1 comment
Read more

If we detect N photons from a coherent state of light for a measurement,

By Steve Rogers,
Short answer: A good order of magnitude rule of thumb for the maximum possible bandwidth of an optical fibre channel is about 1 petabit per second per optical mode. So a "single" mode fibre (fibre with one bound eigenfield) actually has in theory two such channels, one for each polarisation state of the bound eigenfield. I'll just concentrate on the theoretical capacity of a single, long-haul fibre; see roadrunner66's answer for discussion of the branching in an optical network. The fundamental limits always get down to a question of signal to noise in the measurement (i.e. demodulation by the receiver circuit). The one, fundamentally anavoidable, noise source on a fibre link is quantum shot noise, so I'll concentrate on that. Therefore, what follows will apply to a short fibre: other noise sources (such as Raman, amplified spontaneous emission from in-line optical amplifiers, Rayleigh scattering, Brillouin scattering) tend to become significant roughly in pro...
2 comments
Read more

The cable types, the cable network hardware

By Steve Rogers,
The ways to build the OSP cables are specifically oriented to the strength of the cable, depending on whether they are buried directly or inside conductors, located underwater, or installed in the air on poles. The proper way for cable routing must be chosen. In some installations, several types of cable are even used. Having good construction plans can be useful when working with cable manufacturers to find the right types of cables and request sufficient quantities. You should always request more cable than is needed for the length of the path, in order to be able to store the service cable in the form of a loop, prepare the termination of the cable and save what you need in case it is necessary to Make a repair in the future. As well as the cable types, the cable network hardware types are very diverse and should be chosen in a way that is compatible with the cable types used. With so many hardware options, working with cable manufacturers is the most expeditious way to choose ha...
2 comments
Read more