Skip to main content

OPTIMIZED FIBER TERMINATION

By Steve Rogers,
In the last session of the fiber optic training program , participants are entitled to take the FO-301 certification exam. By taking and passing this certification exam, participants are entitled to obtain the NCFT (NetCampus Certified Fiber Optic Technician) degree as a validity of their expertise in designing and installing indoor and outdoor fiber optic media for corporate computer networks.
Training materials

OPTIMIZED FIBER TERMINATION
- Introduction of fiber optic cables, slites, and connectors and calculation of FO material requirements.
- Light sources, light detectors, optical transmission planning and design.
- Cable stripping and optical fiber termination
- Measurement with power meter and Trouble Shooting optical fiber
- Frequently Asked Questions
fiber optic certified
SPLICING AND OTDR
- Basics of optical fiber and OTDR measurement
- Fiber Optic Stripping - Fiber Optic
Splicing
- OTDR measurement and interpretation
- Frequently Asked Questions

BONUS : Fiber optic training participants get the opportunity to participate in " Fundamental IoT " training activities for free. For more information about FO training and IoT fundamentals, please contact our sales team.

Comments

Post a Comment

Popular posts from this blog

If we detect N photons from a coherent state of light for a measurement,

By Steve Rogers,
Short answer: A good order of magnitude rule of thumb for the maximum possible bandwidth of an optical fibre channel is about 1 petabit per second per optical mode. So a "single" mode fibre (fibre with one bound eigenfield) actually has in theory two such channels, one for each polarisation state of the bound eigenfield. I'll just concentrate on the theoretical capacity of a single, long-haul fibre; see roadrunner66's answer for discussion of the branching in an optical network. The fundamental limits always get down to a question of signal to noise in the measurement (i.e. demodulation by the receiver circuit). The one, fundamentally anavoidable, noise source on a fibre link is quantum shot noise, so I'll concentrate on that. Therefore, what follows will apply to a short fibre: other noise sources (such as Raman, amplified spontaneous emission from in-line optical amplifiers, Rayleigh scattering, Brillouin scattering) tend to become significant roughly in pro
2 comments
Read more

ingle-mode fiber uses only one mode of light to propagate

By Steve Rogers,
Single-mode fiber uses only one mode of light to propagate through the fiber-optic core. In single-mode fiber-optic cabling, the core is considerably smaller (8 to 10 microns) in diameter. A 9/125 optical fiber indicates that the core fiber has a diameter of 9 microns and the surrounding cladding is 125 microns in diameter. The core in single-mode fiber is only approximately 10 times larger than the wavelength of the light it is carrying. This leaves very little room for the light to bounce around. As a result the data carrying light pulses in single-mode fiber are essentially transmitted in a straight line through the core. Typically single-mode uses a laser light source, which is more expensive to produce, requires higher levels of safety awareness, and can transmit data further than multimode. Single-mode (such as a 9/125) can carry data up to 3000 meters (9,840 ft.) according to the existing standard (note that the standard in this case may not reflect the physical limitation)
Post a Comment
Read more

Copper, fiber or wireless network?

By Steve Rogers,
While for decades the debate about which one is better (copper, fiber or wireless network), increased interest in discussing wiring, it is now becoming irrelevant.  In communications technology and the end-user market, it seems, it has already been decided that, in general terms, the transmission media and many networks must combine all three.  Currently, for the designer of wiring networks, especially fiber optic networks, and for their clients, the task of deciding which means to use once the communication systems were chosen is very simple. Long-distance and external plant Almost all telephony system cables are fiber optic, except telecommunications systems that still use copper for the final connection to the home.  CATV companies use a high-performance coaxial cable inside homes, but it connects to a  fiber optic  backbone  network .  Backbone (  backbone  ) Internet consists of fiber in its entirety.  Most commercial buildings that are in heavily populated areas receive d
1 comment
Read more